Εξαερώστε το σύστημα συμπλέκτη

This function describes how to bleed the clutch hydraulics.
Μετά την αντικατάσταση της μετάδοσης, η μονάδα συμπλέκτη με τον ρυθμιστή MTA ή μέρη του υδραυλικού συστήματος συμπλέκτη ή η υδραυλική γραμμή έχει ανοίξει ή να είναι ξεφόρτιστη πρέπει τα υδραυλικά του συμπλέκτη να εξαερωθούν.
Σημείωση:
Για να σιγουρέψετε την λειτουργία του συμπλέκτη. η εξαέρωση πρέπει να γίνει μόνο με ένα διαγνωστικό εργαλείο και ένα εργαλείο εξαέρωσης φρένων. Η χειροκίνητη εξαέρωση δεν επιτρέπεται. Παρακαλώ σημειώστε τις οδηγίες του κατασκευαστή πριν χρησιμοποιήσετε το εργαλείο εξαέρωσης φρένων.
Συνθήκες ελέγχου:
Διαδικασία:
  1. Install the brake bleeding tool (Observe the manufacture's instructions). Enlist the support of TIS (Technical information) from Opel's website: www.gme-infotech.com
  2. Bleed the hydraulic clutch system (step 1): Open the bleed nipple (Make sure that the bleed nipple is open at least 180° to reach the correct bleeding).
  3. Allow the liquid to drain from the bleed nipple until it is clear and without bubbles, then close the bleed nipple.
  4. Empty the bleed reservoir (if needed).
  5. Bleed the hydraulic clutch system with the diagnostic tool (step 2): 2 mechanics is required.
  6. Enter the program function "Component activation" and select clutch activation.
  7. Open the bleed nipple.
  8. Activate the clutch activation 15 times (On, then Off) in intervals of one second.
  9. Allow the liquid to drain from the bleed nipple until it is clear and without bubbles, then close the bleed nipple.
  10. Empty the bleed reservoir (if needed).
  11. Bleed the hydraulic clutch system with the diagnostic tool (step 3): 2 mechanics is required.
  12. Activate the clutch activation (On) to pressurize the clutch hydraulic system, immediately open the bleed nipple, then close the bleed nipple.
  13. Deactivate the clutch activation (Off) to bleed the pressure in the clutch hydraulic system.
  14. Repeat step 3 for at least 10 minutes until the liquid is clear and without bubbles.
  15. Empty the bleed reservoir (if needed).
  16. Do not engage any gears yet.
  17. Start the engine and let it idle for 10 seconds, then stop the engine.
  18. Repeat step 1 of the bleeding procedure.
  19. Repeat step 2 of the bleeding procedure.
  20. Repeat step 3 of the bleeding procedure.
  21. Remove the brake bleeding tool. Enlist the support of TIS (Technical information) from Opel's website: www.gme-infotech.com
  22. Perform the programming of the clutch hydraulic system.
Αν η λειτουργία αποτύχει, ελέγξτε τις προϋποθέσεις δοκιμής και επιδιορθώστε οποιαδήποτε σφάλματα.